![]() The 5" pneumatic is just so quick and easy to get out, that is happens, but I would rather use the ETS EC 125 for the dust extraction. I use them less in recent years because of my move into Festool, but they do still get used, probably about 20-25%. My 5" palm-style random orbit sander and 2 of the 8" geared orbital sanders are all nearly 4 years old and have never been oiled beyond whatever the factory did to them. I have continued with this practice to this day. This eliminates one potential source of contamination/fisheyes. If it happens to die prematurely, so be it. That is to never put oil into sanders.ever. There I learned an abusive thing, that is very apparently common in that field. I worked in a body shop for years, long before I ever stepped into a cabinet shop. Sanders use a lot more air, for a lot longer periods of time though. I wasn't even aware that this was an issue? I have seen exhaust ports from palm sanders get pretty wet from it though, so the potential is there. I have never had oil from a nail/staple gun foul anything. A drop or 2 once in a while, is all it takes. What is supposed to be better about oil-less? It's not like the regular ones are cumbersome. It comes in a Systainer that matches all of the Festool ones, even the color. It's an easy fix, but does take a hex key, rather than a simple buckle. It never comes out to damage the workpiece. The jambs are always a mis-fire internally, where the pin just kind of crumbles. The one I occasionally struggle with is the Cadex V2/21 It does jamb once in a while. FinishPro18mg It has been just as dependable. It doesn't need to happen often for me, but it has been enough of a thing that I know about it. There is a mechanism that locks the trigger which is controlled by the fact that pins are indeed installed, but it is high enough in the magazine that pins under 5/8" cannot depress it. The one thing it won't do is shoot very short pins. They call the older one "Industrial" but I don't really know what that means? I have had it nearly 4 years and it has never failed me, jambed etc. When I bought mine in '19 it sold for $154, now that same unit sells for $271? I'm not entirely sure what the deal is though? The newer model is considerably cheaper, like $100 cheaper. 8F0001N It came before the oilless, but they are still available. Corded equipment is cheaper, never has to have batteries swapped out, an in terms of my drill, it spins faster without any inconvenient battery changes. In any case, consider where and how you use the equipment. Forgot to mention that Logitech recommended that I replace the batteries once a year, even if they were still going strong. What possible advantage is the rechargeable? I’m to recharge once a week (recommended), and when the battery dies, I’ll have to toss it in the garbage. ![]() My new, more expensive, Apple wireless keyboard has a rechargeable battery. The instructions said that they were good for three million keystrokes, and that there was no current draw when it was idle. My old Logitech wireless keyboard used 2 double A batteries. The world is too much in love with rechargeable batteries. I’m not interested in a battery powered sander. Most of my sanding is done at my workbench. The point being, consider where and how you will be using equipment before deciding on how it should be powered. I had a ladder, the compressor, a 15 foot hose, and I had to plug in from the kitchen as there was no wall outlet. I was remodeling a powder room and the pneumatic P-C made the room too crowded. I would note that I replaced my P-C 15 gage nailer with a battery powered Milwaukee. I know many carpenters that swear by their Sencos, but also that perhaps their quality has gone down since Kyocera bought them out in 2017. I know the Cadex and Grex get pretty decent reviews, too, but like the idea of going oilless with the Sencos. Apparently Metabo bought Hitachi's power tool division out some years ago. I could just get the Metabo HPT NP35A, which is a 23-gauge pin nailer for $80. Maybe they just haven't been around long enough, but anyone here use them? This is intriguing for me, I never like oiling my Hitachi and my oil-less compress has lasted decades (although I am replacing that with a quieter one).Īnyway, there aren't many reviews on the Sencos (models TN21L1, TN11L1, and TN11G1 - don't ask me why the 21 gauge is TN21L2 while the 23 gauge isn't TN23L1). Senco introduced two 23-gauge and one 21-gauge nailers just a couple/few years ago that are oil-less. The 23-gauge would be for where I can't easily clamp something while the glue dries. Been using my trusty old Hitachi 18-ga brad nailer for trim jobs (like baseboards), but thinking about going for a 21 and/or 23 gauge nailer where I don't need the 2" length and want a smaller hole.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |